Epoxy flooring training in Texas

Texas makes it simple to start a coating business, and it has more hands-on epoxy classes than any other state we track. There is no state license for the work, and an LLC is one form and one yearly report. What Texas demands instead is discipline: insurance your customers can check, written contracts, and a summer schedule built around the heat.

Do you need a license for epoxy floors in Texas?

No. Texas has no state license for general contractors, remodelers, flooring installers or coating contractors. The state licenses specific trades, such as electricians and air conditioning contractors, through the Texas Department of Licensing and Regulation. Texas once registered residential builders, but that program was abolished effective September 1, 2010.

That leaves three things to handle yourself:

• Licensed trades on your jobs. If a job needs electrical work, for example a new circuit for a garage heater, a licensed electrician does it. You can check any trade license on the TDLR license search.
• City permits and registration. Whether coating an existing floor needs a permit is a city decision, and some cities require contractors to register before they pull any permit. Ask the permit office in each city you work in.
• Proof for your customers. With no state license to look up, homeowners and general contractors judge you by your insurance certificate, your contract and your reviews. Have the certificate ready before the first estimate.

Where to take an epoxy class in Texas

Nine providers run hands-on classes in Texas, more than in any other state we track, and six of them are in Dallas–Fort Worth. The table further down lists each one; here is how they compare.

Most one-day classes are run by suppliers around the products they sell, which makes them a cheap way to learn one system. The multi-day classes are where you practice a full install. New Era teaches its four days in English and Spanish, and the Garland class is meant for working installers who apply first.

If you’re near the Red River, Polished Concrete University also runs a three-day version of its course in Oklahoma City for $1,350.

Setting up the business: LLC, franchise tax and workers’ comp

Forming an LLC costs $300 with the Texas Secretary of State (Form 205, the certificate of formation). Texas has no annual report fee, but every LLC deals with the Comptroller each year. Reports are due May 15. If your annualized revenue is at or below the no-tax-due threshold, $2,650,000 for 2026 and 2027 reports, you owe no franchise tax and file only a Public Information Report. Above it, you file the franchise tax report itself. Skip the filing and the state can forfeit your LLC’s right to do business.

Workers’ compensation is where Texas differs from every other state. Most private employers may choose not to carry it. An employer that goes without must tell the state it has no coverage and must report work injuries that cost more than a day of work. General contractors and commercial customers often ask for proof of coverage before you start, so price the policy into your plan even if the law doesn’t force it, and talk it through with an insurance agent.

Safety rules are federal in Texas. There is no state OSHA plan for private employers, so federal OSHA enforces the silica standard that applies when you grind concrete. A grinder connected to a dust extractor built for silica dust is the normal way to meet it.

VOC limits for floor coatings start from the national cap of 400 grams per liter. If you also take jobs in states with their own, lower limits, such as California (50 g/L) or Ohio and New York (100 g/L), check the VOC figure on the data sheet before you stock a system.

Heat, humidity and the occasional freeze: installing in Texas

A typical high-solids floor epoxy, such as Sherwin-Williams ArmorSeal 1000 HS, needs air, slab and material between 50°F and 120°F, relative humidity no higher than 85%, and a slab at least 5°F warmer than the dew point. A typical polyaspartic, such as Deco-Crete’s Polyaspartic 90, works best between 60°F and 90°F.

Texas covers several climates:

Ranges are the lowest and highest monthly averages across the year. Morning readings are taken at 6 a.m. and midday readings at noon in Central time.

What that means on the job:

• Houston is a humidity problem. Average morning humidity runs 85–93% in every month, at or above the 85% ceiling on most data sheets. Prep early, coat late morning or later, and read the slab, not the forecast.
• Dallas and Austin are a heat problem. Normal August highs of 97–98°F cut working time hard: the ArmorSeal epoxy gives you 4 hours of pot life at 77°F and 2 hours at 120°F, and the Deco-Crete polyaspartic is rated at 15–20 minutes for a 100-gram mass, shorter in heat. Mix smaller batches, keep kits out of the truck and the sun, and start coats in the cooler part of the day.
• Winters still bite. Dallas’s normal January low is 37.9°F and El Paso’s 34.5°F, below the 50°F minimum on many epoxies. Cold-weather polyaspartics exist for this; check the slab temperature before you open a kit.
• El Paso is the opposite of Houston. Midday humidity averages 16–37%, so humidity is rarely the limit there; temperature is.
• Test every slab for moisture. Data sheets require a calcium chloride test (ASTM F1869) or an in-slab humidity test (ASTM F2170) before you coat.

Set cure times in writing: the ArmorSeal epoxy takes foot traffic after 24 hours at 77°F and fully cures in 7 days, and the polyaspartic above takes vehicles after 7 days.

Where the work is in Texas

Texas had 31,709,821 residents on July 1, 2025, second only to California, and added 391,243 people that year, more than any other state. Four of the ten fastest-growing metro areas by number of people are in Texas: Houston–Pasadena–The Woodlands (7,904,627, up 126,720, the most in the country), Dallas–Fort Worth–Arlington (8,477,157, up 123,557), Austin–Round Rock–San Marcos (2,620,945) and San Antonio–New Braunfels (2,813,140).

The growth is in the suburbs. Harris County added more people than any county in the country, and Collin, Montgomery and Fort Bend counties are also among the eight that added the most. Those are the places where new garages, new owners and new commercial buildings are being added fastest.

Epoxy Business School classes in Texas

Epoxy Business School hasn’t scheduled a Texas class yet. Classes open state by state with partner trainers who install floors for a living, in the states where enough people ask for them. Before the two days on the slab, students complete The Epoxy Playbook: recorded installation training, with full installs you can replay, plus the business side of pricing, quoting and selling. It’s required before the hands-on class.

If you’re in Texas, leave your number below and we’ll text you when a class is set. Starting now instead? Run your numbers in the startup cost calculator, and check the license requirements by state if you’ll also work in Oklahoma, Louisiana or New Mexico, which each set their own rules.